WJIECO 227930700R PM Sensor Cross Bosch OEM 0281007573 0281007574 for Renault Trafic III Master III Nissan NV300 Fiat Talento Diesel

227930700R PM Sensor Overview

The 227930700R PM Sensor (Renault OE# 227930700R, Bosch OEM# 0281007573, 0281007574) is an OEM-grade DPF PM Sensor engineered by WJIECO for Euro6 diesel light commercial vans. Also known as soot sensor, this critical aftertreatment component mounts downstream of the Diesel Particulate Filter (DPF). It detects the concentration of fine particulate soot in exhaust gas leaving the DPF and transmits real-time particulate readings to the ECU. The ECU uses this signal to trigger, regulate and monitor DPF automatic regeneration, which is mandatory for Euro 6 diesel emissions compliance.

This PM Sensor is designed as a direct factory replacement for these applications: Renault Trafic III 1.6dCi, Renault Master III 2.3dCi, Nissan NV300 1.6dCi, Fiat Talento 1.6dCi.

If your Renault, Nissan or Fiat diesel vehicle triggers a persistent check engine light, DPF regeneration failure, forced limp mode, soot overload warning or particulate related diagnostic trouble codes, your factory PM Sensor is likely suffering from probe contamination, carbon soot fouling, signal drift or internal circuit aging damage. Replacing the defective original sensor with this direct-fit 227930700R replacement part is a cost-effective solution to restore your diesel aftertreatment system.

OEM-Grade Construction and Strict Factory Testing

Our replacement 227930700R PM Sensor features a precision soot detection probe and reinforced anti-vibration internal circuit module. It is engineered to withstand extreme exhaust temperature, thermal cycling and vibration during city stop-and-go traffic and long-distance highway cruising. The outer protective housing, wiring harness and multi-pin electrical plug connector are fully dimension-matched to Renault OEM and Bosch factory specifications, preventing wire cracking, water ingress and intermittent signal dropouts.

https://www.amazon.com/dp/B0F4XKV1VT

Every finished PM Sensor unit goes through high-temperature aging testing, soot signal calibration and waterproof sealing inspection before shipment. This quality check eliminates common flaws found in cheap generic sensors, such as unstable particulate readings, slow signal response and early premature failure under high soot loads.

Exact Vehicle Compatibility & Interchange OE Numbers

This DPF downstream PM Sensor is a direct replacement for the below Euro6 diesel light commercial vehicles. Interchange Part Numbers:

• Renault OE: 227930700R
• Bosch OEM: 0281007573, 0281007574

Fitment List:

• Renault Trafic III 1.6dCi
• Renault Master III 2.3dCi
• Nissan NV300 1.6dCi
• Fiat Talento 1.6dCi

As a core component of Euro 6 diesel exhaust aftertreatment system, this PM Sensor allows the ECU to evaluate DPF filtration efficiency and manage regeneration cycles. A faulty PM Sensor will block DPF regeneration, trigger limp mode, cause DPF clogging and illuminate the check engine light. Common DTCs include P2452, P2453, P2454, P2463.

Replacing your malfunctioning factory DPF soot detector with our pre-calibrated WJIECO 227930700R PM Sensor delivers noticeable reliability improvements and protects expensive diesel particulate filters. Unlike low-cost aftermarket sensors that repeatedly trigger fault codes due to poor calibration, our unit provides steady, accurate soot concentration data for the vehicle ECU.

https://wjieco-autoparts.com/product/227930660r-pm-sensor/#tab-description

Reliable sensor measurements enable the engine computer to execute normal DPF regeneration, avoid unplanned limp mode, reduce DPF soot buildup and keep your diesel vehicle compliant with Euro 6 emission regulations. After installation, you can clear particulate sensor related trouble codes and restore full engine power.

Plug-and-Play Installation, No Dealer Programming Required

A key advantage of this 227930700R PM Sensor is its true plug-and-play design built for compatible Euro6 diesel van models. This replacement part requires no ECU reprogramming, manual calibration, wire cutting or complicated mechanical modifications.

Installation works well for both professional repair garages and DIY vehicle owners. Simply remove the old PM Sensor from the exhaust pipe after DPF, apply anti-seize compound on threads, align and screw in the new sensor, reconnect the factory wiring plug, then clear stored fault codes using an OBD diagnostic scanner. After a short normal driving cycle, the DPF aftertreatment system will return to stable operation without recurring warning alerts.

Every WJIECO PM Sensor passes complete functional testing before leaving our factory. If you need a durable, high-precision and affordable OEM replacement DPF PM Sensor matching Renault OE 227930700R and Bosch OEM 0281007573 / 0281007574 for your Renault Trafic III, Master III, Nissan NV300 or Fiat Talento, our 227930700R PM Sensor is the ideal choice to restore your diesel exhaust aftertreatment system.