WJIECO JN15-5L239-BC PM Sensor DPF Diesel Particulate Filter Sensor for Ford ECOSPORT 1.5TDCi 2015-2019 diesel. Cross reference OEM 2275529, Bosch OEM 0281007563. Plug-and-play, fixes DPF regeneration & particulate fault codes.

JN15-5L239-BC PM Sensor Overview

The JN15-5L239-BC PM Sensor (Ford OE# JN15-5L239-BC, Alternate OEM#2275529, Bosch OEM# 0281007563) is an OEM-grade DPF PM Sensor engineered by WJIECO for Ford ECOSPORT 1.5TDCi 2015-2019 diesel vehicles. Also known as soot sensor, this critical aftertreatment component mounts downstream of the Diesel Particulate Filter (DPF). It detects the concentration of fine particulate soot in exhaust gas leaving the DPF and transmits real-time particulate readings to the ECU. The ECU uses this signal to trigger, regulate and monitor DPF automatic regeneration, which is mandatory for modern diesel emissions compliance.

This JN15-5L239-BC PM Sensor is designed as a direct factory replacement for these applications: Ford ECOSPORT 1.5TDCi, Model Year 2015 to 2019.

https://www.amazon.com/dp/B0F4XHFWFD

If your Ford ECOSPORT diesel SUV triggers a persistent check engine light, DPF regeneration failure, forced limp mode, soot overload warning or particulate related diagnostic trouble codes, your factory PM Sensor is likely suffering from probe contamination, carbon soot fouling, signal drift or internal circuit aging damage. Replacing the defective original sensor with this direct-fit JN15-5L239-BC PM Sensor replacement part is a cost-effective solution to restore your diesel aftertreatment system.

H2: OEM-Grade Construction and Strict Factory Testing

Our replacement JN15-5L239-BC PM Sensor features a precision soot detection probe and reinforced anti-vibration internal circuit module. It is engineered to withstand extreme exhaust temperature, thermal cycling and strong vibration during highway cruising and heavy load driving conditions. The outer protective housing, wiring harness and multi-pin electrical plug connector are fully dimension-matched to Ford OEM and Bosch factory specifications, preventing wire cracking, water ingress and intermittent signal dropouts.

Every finished JN15-5L239-BC PM Sensor unit goes through high-temperature aging testing, soot signal calibration and waterproof sealing inspection before shipment. This quality check eliminates common flaws found in cheap generic sensors, such as unstable particulate readings, slow signal response and early premature failure under high soot loads.

H2: Exact Vehicle Compatibility & Interchange OE Numbers

This DPF downstream JN15-5L239-BC PM Sensor is a direct replacement for the below diesel model (Fitment reference from Amazon US & eBay): Ford OE: JN15-5L239-BC Alternate OEM: 2275529 Bosch OEM: 0281007563 Fitment List:

• Ford ECOSPORT 1.5TDCi 2015-2019 Diesel

As a core component of modern diesel exhaust aftertreatment system, this JN15-5L239-BC PM Sensor allows the ECU to evaluate DPF filtration efficiency and manage regeneration cycles. A faulty PM Sensor will block DPF regeneration, trigger limp mode, cause DPF clogging and illuminate the check engine light. Common DTCs include P2452, P2453, P2454, P2463.

https://wjieco-autoparts.com/product/jn15-5l239-ac-pm-sensor/

WJIECO JN15-5L239-AC PM Sensor DPF Diesel Particulate Filter Sensor for Ford Transit & Tourneo Custom 2.0 EcoBlue diesel. Cross reference OEM 2269288, Bosch OEM 0281007565. Plug-and-play, fixes DPF regeneration & particulate fault codes. – WJIECO

H2: Core Benefits of Upgrading to the JN15-5L239-BC PM Sensor

Replacing your malfunctioning factory DPF soot detector with our pre-calibrated WJIECO JN15-5L239-BC PM Sensor delivers noticeable reliability improvements and protects expensive diesel particulate filters. Unlike low-cost aftermarket sensors that repeatedly trigger fault codes due to poor calibration, our unit provides steady, accurate soot concentration data for the vehicle ECU.

Reliable sensor measurements enable the engine computer to execute normal DPF regeneration, avoid unplanned limp mode, reduce DPF soot buildup and keep your Ford ECOSPORT compliant with emissions regulations. After installation, you can clear particulate sensor related trouble codes and restore full engine power.

H2: Plug-and-Play Installation, No Dealer Programming Required

A key advantage of this JN15-5L239-BC PM Sensor is its true plug-and-play design built for compatible Ford ECOSPORT 1.5TDCi 2015-2019. This replacement part requires no ECU reprogramming, manual calibration, wire cutting or complicated mechanical modifications.

Installation works well for both professional repair garages and DIY vehicle owners. Simply remove the old PM Sensor from the exhaust pipe after DPF, apply anti-seize compound on threads, align and screw in the new sensor, reconnect the factory wiring plug, then clear stored fault codes using an OBD diagnostic scanner. After a short normal driving cycle, the DPF aftertreatment system will return to stable operation without recurring warning alerts.

Every WJIECO JN15-5L239-BC PM Sensor passes complete functional testing before leaving our factory. If you need a durable, high-precision and affordable OEM replacement DPF PM Sensor matching Ford OE JN15-5L239-BC, alternate OEM 2275529 and Bosch OEM 0281007563 for your Ford ECOSPORT 1.5TDCi 2015-2019, our JN15-5L239-BC PM Sensor is the ideal choice to restore your diesel exhaust aftertreatment system.