WJIECO 227936996R PM Sensor Long-lasting Cross Bosch OEM 0281008402 0281008403 for Renault Kadjar Koleos II Clio V Dacia Duster II Diesel

227936996R PM Sensor Overview

The 227936996R PM Sensor (Renault OE# 227936996R, Bosch OEM# 0281008402, 0281008403) is an OEM-grade DPF PM Sensor engineered by WJIECO for Euro6 diesel Renault and Dacia passenger vehicles. Also known as soot sensor, this critical aftertreatment component mounts downstream of the Diesel Particulate Filter (DPF). It detects the concentration of fine particulate soot in exhaust gas leaving the DPF and transmits real-time particulate readings to the ECU. The ECU uses this signal to trigger, regulate and monitor DPF automatic regeneration, which is mandatory for Euro 6 diesel emissions compliance.

This PM Sensor is designed as a direct factory replacement for these applications: Renault Kadjar 1.6dCi, Renault Koleos II 2.0dCi, Renault Clio V 1.5dCi, Dacia Duster II 1.5dCi.

If your Renault or Dacia diesel vehicle triggers a persistent check engine light, DPF regeneration failure, forced limp mode, soot overload warning or particulate related diagnostic trouble codes, your factory PM Sensor is likely suffering from probe contamination, carbon soot fouling, signal drift or internal circuit aging damage. Replacing the defective original sensor with this direct-fit 227936996R replacement part is a cost-effective solution to restore your diesel aftertreatment system.

OEM-Grade Construction and Strict Factory Testing

Our replacement 227936996R PM Sensor features a precision soot detection probe and reinforced anti-vibration internal circuit module. It is engineered to withstand extreme exhaust temperature, thermal cycling and vibration during city stop-and-go traffic and long-distance highway cruising. The outer protective housing, wiring harness and multi-pin electrical plug connector are fully dimension-matched to Renault OEM and Bosch factory specifications, preventing wire cracking, water ingress and intermittent signal dropouts.

Every finished PM Sensor unit goes through high-temperature aging testing, soot signal calibration and waterproof sealing inspection before shipment. This quality check eliminates common flaws found in cheap generic sensors, such as unstable particulate readings, slow signal response and early premature failure under high soot loads.

Exact Vehicle Compatibility & Interchange OE Numbers

This DPF downstream PM Sensor is a direct replacement for the below Renault / Dacia Euro6 diesel vehicles. Interchange Part Numbers:

• Renault OE: 227936996R
• Bosch OEM: 0281008402, 0281008403

Fitment List:

• Renault Kadjar 1.6dCi
• Renault Koleos II 2.0dCi
• Renault Clio V 1.5dCi
• Dacia Duster II 1.5dCi

As a core component of Euro 6 diesel exhaust aftertreatment system, this PM Sensor allows the ECU to evaluate DPF filtration efficiency and manage regeneration cycles. A faulty PM Sensor will block DPF regeneration, trigger limp mode, cause DPF clogging and illuminate the check engine light. Common DTCs include P2452, P2453, P2454, P2463.

Core Benefits of Upgrading to the 227936996R PM Sensor

Replacing your malfunctioning factory DPF soot detector with our pre-calibrated WJIECO 227936996R PM Sensor delivers noticeable reliability improvements and protects expensive diesel particulate filters. Unlike low-cost aftermarket sensors that repeatedly trigger fault codes due to poor calibration, our unit provides steady, accurate soot concentration data for the vehicle ECU.

Reliable sensor measurements enable the engine computer to execute normal DPF regeneration, avoid unplanned limp mode, reduce DPF soot buildup and keep your diesel vehicle compliant with Euro 6 emission regulations. After installation, you can clear particulate sensor related trouble codes and restore full engine power.

Plug-and-Play Installation, No Dealer Programming Required

A key advantage of this 227936996R PM Sensor is its true plug-and-play design built for compatible Renault and Dacia Euro6 diesel models. This replacement part requires no ECU reprogramming, manual calibration, wire cutting or complicated mechanical modifications.

Installation works well for both professional repair garages and DIY vehicle owners. Simply remove the old PM Sensor from the exhaust pipe after DPF, apply anti-seize compound on threads, align and screw in the new sensor, reconnect the factory wiring plug, then clear stored fault codes using an OBD diagnostic scanner. After a short normal driving cycle, the DPF aftertreatment system will return to stable operation without recurring warning alerts.

Every WJIECO PM Sensor passes complete functional testing before leaving our factory. If you need a durable, high-precision and affordable OEM replacement DPF PM Sensor matching Renault OE 227936996R and Bosch OEM 0281008402 / 0281008403 for your Renault Kadjar, Koleos II, Clio V or Dacia Duster II, our 227936996R PM Sensor is the ideal choice to restore your diesel exhaust aftertreatment system.

https://wjieco-autoparts.com/product/227936987r/

https://www.amazon.com/dp/B0F4XKV1VT